EXPERTISE / EXPANSION JOINTS

Bridge expansion joint replacement in Tunisia

BBTP replaces worn expansion joints on bridges and viaducts: removal of the old joints, rebuilding of the reinforced-concrete anchorage zones and installation of new joints, for safe traffic and a structure protected from water.

HOW IT WORKS

What does an expansion joint do?

The expansion joint keeps the running surface continuous across the deck gaps, between two spans or between the deck and the abutment, while allowing the movements caused by temperature, shrinkage, creep and traffic loads.

Directly exposed to traffic impacts, it is one of the most heavily loaded parts of the structure. Once damaged, it becomes noisy and dangerous, and lets water run onto the supports, damaging bearings, plinths and pier caps.

DIAGNOSIS

When should an expansion joint be replaced?

These signs are noted during bridge inspections or reported by road users. Replacing a joint in time avoids far heavier repairs to the supports and the deck.

  • Noise and impacts as vehicles pass
  • Loose, broken or torn-out parts
  • Cracked or spalled anchorage beams
  • Torn sealing strip, leaks onto the supports
  • A step between the joint and the road surface

EXPANSION JOINTS

The main types of expansion joints.

The choice of joint depends mainly on its movement capacity, that is the range of movements to accommodate, and on traffic.

01

Strip seal joints

Two steel edge profiles anchored in the edge beams, linked by a watertight elastomer seal. Suited to small and medium movements.

02

Finger joints

Toothed steel plates, cantilevered or supported, anchored on either side of the gap. They accommodate large movements; a trough collects water under the joint.

03

Reinforced elastomer joints

Elastomer modules reinforced with steel plates, bolted to the anchorage beams. They accommodate movements through shear deformation of the elastomer.

OUR METHOD

Joint replacement in five steps.

  1. Survey

    Survey of the joint opening and movement range, condition of the edge beams, traffic phasing.

  2. Removal

    Saw-cutting the road surface, removing the old joint and breaking out the damaged anchorage concrete.

  3. Anchorage beams

    Reinforcing and casting the new edge beams in reinforced concrete or special mortar.

  4. Installation and setting

    Setting the new joint flush with the road surface, with its opening preset to the deck temperature.

  5. Finishing

    Connection to the waterproofing and road surface, checks, then reopening to traffic.

KEY POINTS

What makes a joint last.

An expansion joint is only as good as its anchorage and installation. Every stage is checked before reopening to traffic.

  • Sound, properly reinforced anchorage beams.
  • Opening preset to the deck temperature.
  • Seamless connection to the waterproofing and road surface.
  • Water drainage to protect the supports.

ON SITE

Our expansion joint work.

All photos ↗

WHY BBTP

Why entrust your expansion joints to BBTP?

01

A speciality

BBTP specialises in maintaining and repairing bridges, including expansion joint replacement and rebuilding their anchorage zones.

02

Field experience

Work in all 24 Tunisian governorates, notably for the Ministry of Equipment.

03

Passed-on know-how

Crews trained by Mohamed Salah Biri, former head of SOMATRA’s structures department.

FAQ

Expansion joints: your questions.

Does the bridge have to be closed to replace an expansion joint?

Usually not: the work is phased one half of the carriageway at a time to keep traffic moving, following a phasing agreed with the owner.

How long does joint replacement take?

It depends on the length of the joint, the type chosen and the traffic phasing. We set the schedule after surveying the structure.

Why does an expansion joint leak?

Over time the sealing profile ages, tears or comes loose, and trapped debris damages it. Water then runs onto the bearings and pier caps and damages the concrete, so a leaking joint must be dealt with quickly.

Can a joint be repaired instead of replaced?

Yes, when the damage is limited: replacing the sealing profile, retightening fixings or local repair of the anchorage concrete. When the joint is too worn or unsuitable, full replacement is the lasting solution.

Where do you work?

Throughout Tunisia. BBTP works in all 24 governorates, notably for the Ministry of Equipment.

A JOINT TO REPLACE?

Let’s talk about your structure.

Project owners, design offices, contractors: tell us about the structure and the defects observed, and we will get back to you.

Contact us